| THIS CAME IN WITH NO MOTOR, TRANS OR REAR. IT'S BEEN PICKED CLEAN AND THE REST SENT TO THE CRUSHER. THIS TRUCK HAD A LOT OF GOOD USABLE PARTS THAT NEED SOME CLEANING OR RESTORING TO BE USED ON A SHOW TRUCK BUT MOST COULD BE USED ON A DRIVER OR CRUISER RIGHT AWAY. A WIRE WHEEL, BUFFER, SOME POLISH, WD-40 AND A LITTLE ELBOW GREASE WOULD CLEAN MOST OF THESE PARTS UP. REMEMBER THESE ARE USED ORIGINAL PARTS OFF AN OLD TRUCK! MOST OF THESE PARTS WILL ALSO FIT OTHER YEARS?? BUT WE'RE NOT POSITIVE SO YOU SHOULD BE. MOST OF THESE PARTS WILL ALSO FIT A 1968 AND A CHEVELLE OR MALIBU?? |
| A PAIR OF FRONT WHEEL WELL OPENING MOULDINGS. THEY ARE ONLY $20 + S/H BECAUSE THEY ARE NOT PERFECT, THEY ARE USED! THE DRIVERS SIDE HAS A FEW OF THE HOLES OUT OF SHAPE (SEE PICTURE) BUT WOULD PROBABLY MOUNT WITH NO PROBLEM WITH THE CORRECT SCREWS WITH THE WASHER BUILT IN. THEY ARE BOTH STRAIGHT (NOT BENT) AND SHOULD POLISH UP NICELY. I MIGHT HAVE 1 OR 2 OF THE ORIGINAL SCREWS TO MATCH UP WITH. AGAIN THE DRIVERS SIDE MOULDING THE HOLES ARE NOT COMPLETE. |
| 1.ALL HEADLIGHT BEZELS 2.HEATER BOX 3.REAR VIEW MIRROR 4.DRIVER SIDE VENT WINDOW REGULATOR 5.VENT WINDOWS 6.DRIVER SIDE DOOR LOCK ROD 7.ROOF RAIL MOLDINGS 8.PASSENGER SIDE FRONT FENDER TRIM 9.DOME LIGHT SWITCHES 10.REAR COIL SPRINGS 11.PARKING LIGHTS 12.GRILL BRACKETS 13.BUMPER BRACKETS 14.GLOVE BOX DOOR 15.TONNEAU COVER BOWS 16.DASH EMBLEM 17.REAR KICK PANELS 18.INTERIOR LIGHT ASSEMBLY 19.HOOD RELEASE 20.STORAGE INSERT 21.SUN VISORS 22.GLOVE BOX STRIKER HOOD HINGES 23.ARM RESTS 24.HOOD CATCH 25.HEADER PANEL 26.ASHTRAY BRACKET 27.GLOVE BOX LIGHT 28.WIPER ARMS 29.FRAME 30.DOOR SKINS 31.GAS PEDAL 32.SEATBELT CLIPS 33.TAIL LIGHTS 34.RIGHT FRONT FENDER 35.GRILLE 36.HEADER PANEL 37.DRIVER SIDE FRONT FENDER 38.BOTH INNER FENDERS 39.FRONT BUMPER 40.PASSENGER SIDE VENT WINDOW REGULATOR |
| BED FLOOR |
| BED FLOOR CLOSE-UPS |
| 1969 CHEVY EL CAMINO |
| SOLD AND BAD PARTS |
| ENGINE TO FRAME GROUNDING STRAP WITH ORIGINAL BOLT. THE ENGINE SIDE WILL MORE THAN LIKELY NEED A NEW TERMINAL END? |
| 8 ORIGINAL HEADLIGHT ADJUSTMENT SCREWS IN USABLE CONDITION UNFORTUNATELY 1 OF THE CLIPS IS BROKEN. |
| 8 ORIGINAL USED WINDSHIELD CHROME TRIM CLIPS |
| FIREWALL HARNESS HOLDER ABOVE THE MASTER CYLINDER WITH THE ORIGINAL SCREW |
| A CLIP WITH ORIGINAL SCREW THATS UNDERNEATH THE COWL ON THE PASSENGER SIDE BUT WE ARE NOT SURE WHAT RUNS THROUGH IT |
| BLACK KICK PANEL GRILL ONLY FOR THE PASSENGER SIDE, UNFORTUNATELY THE KICK PANEL IS NO GOOD |
| PASSENGER SIDE WINDOW REGULATOR WITH ORIGINAL BOLTS AND TRACKING |
| DRIVER SIDE WINDOW REGULATOR WITH ORIGINAL BOLTS AND TRACKING |
| BLACK KICK PLATE. THIS KICK PLATE GOES ON THE FLOOR UNDER THE FUSE BOX AND STEERING COLUMN. IT HAS BOTH THE ORIGINAL SCREWS AND A PART# 3947979-2 ON THE BACK. IT HAS A SMALL HAIRLINE CRACK THAT'S NOT NOTICEABLE UNLESS YOU'RE HOLDING THE PART IN YOUR HAND |
| PASSENGER VENT WING WINDOW REGULATOR WITH ALL ORIGINAL BOLTS AND IT DOES WORK GOOD |
| 1 SET OF UPPER AND LOWER PASSENGER SIDE DOOR HINGES WITH ORIGINAL BOLTS. THESE HINGES DO HAVE SURFACE RUST BUT ARE SOLID AND DO WORK FREELY. DRIVERS SIDE HINGES ALSO AVAILABLE |
| WIRING HARNESS HOLDER THAT GOES IN THE CENTER OF THE FIREWALL. IT DOESN'T COME WITH ANY SCREWS BECAUSE IT DIDN'T HAVE THE ORIGINALS IN IT |
| DRIVER SIDE ONLY (PASSENGER SIDE WAS SOLD) FRONT FENDER CHROME PIECE. THIS PIECE IS IN GOOD CONDITION. IT GOES ON THE TOP EDGE OF THE FENDER AT THE DOOR |
| FRONT DRIVERS SIDE FENDER CHROME. THIS CHROME PIECE DOES HAVE SCRATCHES AND SMALL DINGS BUT WE THINK IT WILL CLEAN UP NICELY |
| 5 OF 6 ORIGINAL FENDER TO BODY BOLTS WITH WASHERS IN GOOD USABLE CONDITION. NOT STRIPPED OR ROUNDED OFF |
| HEADLIGHT RESISTOR BLOCK WITH THE ORIGINAL SCREW. IT MOUNTS ON THE PASSENGER SIDE IN THE ENGINE COMPARTMENT BEHIND THE HEADLIGHTS |
| 2 ORIGINAL WIRING HARNESS HANGERS WITH ORIGINAL NUTS. THESE HANGERS ARE A LITTLE DIRTY AND NEED TO BE STRAIGHTENED OUT |
| WIPER MOTOR BRACKET. THIS BRACKET IS SOLID AND HAS THE RUBBER GASKET AND TWO SCREWS BUT COULD USE A CLEANING |
| COMPLETE PASSENGER SIDE HIGH BEAM HEADLIGHT ASSEMBLY. THE BUCKET WITH TRIM RING AND HEADLIGHT. THE WORKING CONDITION OF THE HEADLIGHT IS UNKNOWN? |
| COMPLETE DRIVER SIDE HIGH BEAM HEAD LIGHT ASSEMBLY. THE BUCKET WITH TRIM RING AND HEAD LIGHT. THE WORKING CONDITION OF THE HEAD LIGHT IS UNKNOWN? |
| COMPLETE DRIVER SIDE LOW BEAM HEADLIGHT ASSEMBLY. THE BUCKET WITH TRIM RING AND HEADLIGHT. WORKING CONDITION OF THE HEADLIGHT IS UNKNOWN? |
| ORIGINAL FENDERWELL BOLTS WITH ORIGINAL WASHERS. WE HAVE ALL 4 ORIGINAL BOLTS AND WASHERS BUT UNFORTUNATELY ONLY 3 SPACERS. THESE BOLTS HOLD THE INNER WHEELWELL TO THE FIREWALL |
| GAS PEDAL CABLE. IT WAS ON A DRAG CAR SO IT WAS WRAPPED AROUND THE GAS PEDAL TO MAKE IT GO FASTER. THIS SHOULD NOT KEEP IT FROM WORKING PROPERLY?? |
| A PAIR OF FRONT FENDER SUPPORT BRACKETS. THESE BRACKETS ARE SOLID BUT COULD USE SOME CLEANING UP |
| PASSENGER SIDE WINDSHIELD POST CHROME. THIS CHROME PIECE DOES HAVE POLISHABLE SCRATCHES AND SILICONE ON THEM (WINDSHIELD MUST HAVE LEAKED) BUT SHOULD CLEAN UP NICELY |
| DRIVER SIDE WINDSHIELD POST CHROME. THIS CHROME PIECE DOES HAVE POLISHABLE SCRATCHES AND SILICONE ON THEM (WINDSHIELD MUST HAVE LEAKED) BUT SHOULD CLEAN UP NICELY |